The common King pellet stove problems include stove not igniting, stove not feeding, poor burn quality, shutting down, low heat, lazy flame, and many more.
Whatever the problem you are struggling with, you can quickly fix that by reading our King Pellet stove troubleshooting guide. So, let’s get started.
Table of Contents
- King Pellet Stove Troubleshooting [ 7 Easy Solutions]
- 1.Stove Not Igniting
- 2.Stove Not Feeding Pellets
- 3.Stove Keeps Shutting Down
- 4.King Pellet Stove Excessive Clinkers
- 5.Low Heat Output Of Stove
- 6.Lazy Flame
- 7. Stove Blackened Glass
- FAQ:
- What Does Error 2 Mean on My King Pellet Stove?
- What Does Error 11 Mean on a King Pellet Stove?
- How Do I Start My King Pellet Stove for the First Time?
- Why Does My King Pellet Stove Keep Overflowing?
- Conclusion
King Pellet Stove Troubleshooting [ 7 Easy Solutions]
The user of the King Pellet stove can face the following problems, and this article will provide the solution to those problems in this writing.
1. Stove Not Igniting
The reasons behind your king pellet stove not igniting are:
- Lousy igniter
- The inappropriate flow of air
- Blown fuse
- Dirty unit, etc.
Solution
King pellet stove not igniting or the poor burn quality problem is easy to solve. The solution starts with cleaning your king pellet stove.
Go with the thorough cleaning and inspecting of the furnace, auger plate, hopper, and switches. And while cleaning, follow the manufacturer’s recommendations when cleaning your stove.
2. Stove Not Feeding Pellets
The king pellet stove not feeding pellets for several reasons. This problem can cause if you don’t close the ash pan door, front door, or hopper lid properly.
Again empty hopper may create a problem for which the stove may stop feeding pellets.
Solutions
Even if you fail to close the doors properly, the king pellet stove has a pressure switch that shuts off the motors.
In case of an empty hopper problem, the solution is to fill the hopper and wait for a few minutes to auger the king pellet stove into a burn pot.
3. Stove Keeps Shutting Down
Flashing the lights of many new units may cause the shutdown of the screen of the King pellet stove.
The common causes of king pellet stove shutting down are:
- Poor air adjustment
- A dirty team
- Inadequate heat trips the stove’s sensors
Also, the furnace’s broken part and work down may cause its constant shutting down.
Solution
Most likely long pellets are the culprits of auger jamming or shutting down the stove.
But the solution is simple also—concise the long pellets of the furnace into a manageable length. You can concise the size of the pellets by dropping bags on the floor.
4. King Pellet Stove Excessive Clinkers
The airflow leak in the king pellet stove is most likely responsible for the excessive clinkers. The partially or burned pellets formed the clinkers.
Solution
If your king pellet stove has excessive clinkers, you can solve the problem by following several general rules.
The easy solution includes cleaning all vents and adjusting the airflow setting or damper. Finally, solve the problem by checking all gaskets and taking steps to repair/replace them if necessary.
5. Low Heat Output Of Stove
The stove’s produced heat rate or ignition rate is proportional to the fuel rate. Therefore air-to-pellet ratio is the likely culprit if your king pellet stove has a low heat output rate.
Solution
If your king pellet stove is suffering from an air-to-pellet ratio problem, the solution is to adjust it by increasing the airflow. Further, you can increase the stove’s feed rate to adjust the Air-to-pellet ratio.
6. Lazy Flame
You will not get your required heat if your stove has a lazy flame, which may lead to shutting down the furnace.
Most probably, the following factors are responsible for the King pellet stove lazy flame:
- The neglected or unclean pellet stove
- Harmful blower exhaust
- Poor air-to-pellet ratio
Solution
Solve the lazy flame problem by taking proper care and maintaining your king pellet stove.
First, properly clean the pellet stove and increase the air adjustments by increasing airflow. Further, decrease the feed rate to increase the stove flame.
7. Stove Blackened Glass
The low burning ratio is responsible for the blackened glass of the king pellet stove. Inadequate fuel or air supply results in poor combusting fire, releasing more by-products.
Removing more products causes blackened glass.
Solution
To solve the blackened glass problem, you need to adjust the heat, air, and fuel setting to the medium and high range.
Then, increase the fuel supply to release minor by-products, and the king pellet stove’s glass remains clean.
FAQ:
What Does Error 2 Mean on My King Pellet Stove?
According to the manual, Error code #2 on the King pellet stove means an empty hopper, fire is burning slowly because of the low fuel quality, jam, or failure in auger output, etc.
What Does Error 11 Mean on a King Pellet Stove?
If you see a flashing “A” on the 5500 king pellet stove’s digital display, there is a complete shutdown in your glass door. Your king pellet stove is probably suffering from the vacuum issue, and it indicates Error 11.
How Do I Start My King Pellet Stove for the First Time?
The control panel of the king pellet stove consists of the “ON” button; press on it. After pressing the ON button, the start-up sequence will begin for the heater. The feed system will get the feed from the fuel through the drill. And approximately after 5 minutes, it will start to ignite.
Why Does My King Pellet Stove Keep Overflowing?
Various factors are responsible for the overflowing of the King pellet stove, including poor quality pellet, ash builds up, etc. Again, if the new shell fails to burn correctly because of the unburnt ammunition, it could cause overflowing.
Conclusion
Hopefully, you could get the solution and fix your heater issue after reading our King pellet stove troubleshooting guide.
Yet, if you are struggling with any other problem, you can let us know in the comment box. We will help you ASAP.